--- pcmcia-cs-3.2.8/etc/wireless.opts
+++ pcmcia-cs-3.2.8/etc/wireless.opts
@@ -39,138 +39,9 @@
 
 case "$ADDRESS" in
 
-# NOTE : Remove the following four lines to activate the samples below ...
-# --------- START SECTION TO REMOVE -----------
 *,*,*,*)
-    ;;
-# ---------- END SECTION TO REMOVE ------------
-
-# Here is an example of scheme matching
-# Activate with "cardctl scheme essidany"
-
-# Pick up any Access Point, should work on most 802.11 cards
-essidany,*,*,*)
     INFO="Any ESSID"
     ESSID="any"
     ;;
 
-# Here are a few examples with a few Wireless LANs supported...
-# The matching is done on the first 3 bytes of the MAC address
-
-# Lucent Wavelan IEEE (+ Orinoco, RoamAbout and ELSA)
-# Note : wvlan_cs driver only, and version 1.0.4+ for encryption support
-*,*,*,00:60:1D:*|*,*,*,00:02:2D:*)
-    INFO="Wavelan IEEE example (Lucent default settings)"
-    ESSID="Wavelan Network"
-    MODE="Managed"
-#    RATE="auto"
-    KEY="s:secu1"
-# To set all four keys, use :
-#   KEY="s:secu1 [1] key s:secu2 [2] key s:secu3 [3] key s:secu4 [4] key [1]"
-# For the RG 1000 Residential Gateway: The ESSID is the identifier on
-# the unit, and the default key is the last 5 digits of the same.
-#   ESSID="084d70"
-#   KEY="s:84d70"
-    ;;
-
-# Cisco/Aironet 4800/340
-# Note : MPL driver only (airo/airo_cs), version 1.3 or later
-*,*,*,00:40:96:*)
-    INFO="Cisco/Aironet example (Cisco default settings)"
-    ESSID="any"
-# To set all four ESSID, use iwconfig v21 and the same trick as above
-    MODE="Managed"
-#    RATE="11M auto"
-#    KEY="off"
-    ;;
-
-# Samsung MagicLan (+ some other PrismII cards)
-# Note : Samsung binary library driver, version 1.20 or later
-*,*,*,00:00:F0:*|*,*,*,00:02:78:*)
-    INFO="Samsung MagicLan example (Samsung default settings)"
-    ESSID="any"
-    MODE="Managed"
-    CHANNEL="4"
-    RATE="auto"
-#    KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
-#    IWCONFIG="power on"
-    ;;
-
-# Raytheon Raylink/WebGear Aviator2.4
-# Note : doesn't work yet, please use for debugging only :-(
-*,*,*,00:00:8F:*|*,*,*,00:00:F1:*)
-    INFO="Raylink/Aviator2.4 example (Aviator default ad-hoc setting)"
-    ESSID="ADHOC_ESSID"
-    MODE="Ad-Hoc"
-    RATE="auto"
-    IWPRIV="set_framing 1"
-    ;;
-
-# Old Lucent Wavelan
-*,*,*,08:00:0E:*)
-    INFO="Wavelan example (Lucent default settings)"
-    NWID="0100"
-    MODE="Ad-Hoc"
-    FREQ="2.425G"
-    KEY="off"
-    ;;
-
-# Netwave (Xircom Netwave/Netwave Airsurfer)
-*,*,*,00:80:C7:*)
-    INFO="Netwave example (Netwave default settings)"
-    NWID="100"
-    KEY="00"
-    ;;
-
-# Proxim RangeLan2/Symphony (what is the MAC address ???)
-*,*,*,XX:XX:XX:*)
-    INFO="Proxim RangeLan2/Symphony example"
-    NWID="0"
-    MODE="Master"
-    CHANNEL="15"
-    IWPRIV="setsubchan 1"
-    ;;
-
-# No Wires Needed Swallow 550 and 1100 setting (what is the MAC address ???)
-*,*,*,XX:XX:XX:*)
-    INFO="NWN Swallow example"
-    ESSID="session"
-    KEY="0000-0000-00 open"
-    ;;
-
-# Symbol Spectrum24 setting (what is the MAC address ???)
-*,*,*,XX:XX:XX:*)
-    INFO="Symbol Spectrum24 example"
-    ESSID="Essid string"
-    ;;
-
-# Generic example (decribe all possible settings)
-*,*,*,*)
-    INFO="Fill with your own settings..."
-    # ESSID (extended network name) : My Network, any
-    ESSID=""
-    # NWID/Domain (cell identifier) : 89AB, 100, off
-    NWID=""
-    # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
-    MODE=""
-    # Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
-    FREQ=""
-    CHANNEL=""
-    # Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
-    SENS=""
-    # Bit rate : auto, 1M, 11M
-    RATE=""
-    # Encryption key : 4567-89AB-CD, s:password
-    KEY=""
-    # RTS threshold : off, 500
-    RTS=""
-    # Fragmentation threshold : off, 1000
-    FRAG=""
-    # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
-    IWCONFIG=""
-    # iwspy parameters : + 01:23:45:67:89:AB
-    IWSPY=""
-    # iwpriv parameters : set_port 2, set_histo 50 60
-    IWPRIV=""
-    ;;
 esac